Hp mediasmart server ex470 linux install#
Hp mediasmart server ex470 linux serial#
Hp mediasmart server ex470 linux password#
Hp mediasmart server ex470 linux windows#

booting from one USB stick to create another wasn't that easy, since all my PC's use UEFI. ItвЂ™s early days, but it seems to run smoothly now. I followed your instructions and installed OMV on the device. I had an old EX490 lying around with some extra RAM installed (and I think I replaced the CPU years ago). As a result, if the server is unplugged for an extended period, it will lose the BIOS settings, and I need to set the BIOS ATA mode again to re-enable drive bays 2 and I doubt if you still follow this thread, but in case you do: My HP Mediasmart is old enough that the CMOS battery is worn out. This appears in OpenMediaVault as a 250MB drive connected to /dev/sda.

Hp mediasmart server ex470 linux windows#

The HP Mediasmart server have a built-in small flash partition for Windows recovery. The health light on the front of the server will continuously flash when it's booted - apparently it does that whenever Windows isn't installed. To read more about those problems, as well as more about how I got the BIOS working to recognize all four drives, see this thread. The server should now reboot again, and when you login again to the OpenMediaVault web interface, drives in all four bays should now be recognized.ДЄs noted above, the internal Ethernet has serious problems. Press PGDN one (1) time to select 4P(IDE)+4S(IDE).

Hp mediasmart server ex470 linux serial#

Press the DOWN arrow eight (8) times to select SIS Serial ATA Mode Press the DOWN arrow one (1) time to select SIS OnChip PCI Device Press the DOWN arrow three (3) times to reach Integrated Peripherals Repeat this process until you're fully comfortable with the process of blindly booting into the BIOS and safely saving and exiting. Press F10 and then ENTER to save and reboot. Advice on the Internet suggests to wait 5 seconds after this to ensure it's in the BIOS. Using a USB keyboard, after power on as soon as the health LED begins to blink blue and red hit DELETE and it'll become solid (either blue or red depending on what it was when you hit delete) and enter the BIOS. This is due to a BIOS setting that will need to be changed. However, you'll note that only the bottom and third from the bottom drive bays are functional. The process was developed by people who hacked VGA output into their servers.ДЄfter a minute or two, I connected to the home server's IP address from a web browser, and the OpenMediaVault interface came up! Doing this a single time seems to apply it every time in the future, as my home server always boots from the USB drive now. After that, I carefully hit the down arrow on the keyboard exactly 7 times, which apparently selects the USB boot option, and then hit enter. There is no harm in over pressing F12, so you can keep pressing to be sure. Apparently, this will bring up the boot menu. Powering on the home server, I repeatedly tapped F12 for 10 seconds. I plugged a USB keyboard into the front USB port. I removed all existing hard drives and inserted the flash drive into the bottom most rear USB port.

Hp mediasmart server ex470 linux password#

Using the root password I set during the installation process, I logged in and deleted the existing network configuration with the following command: Once I had OpenMediaVault installed on my second flash drive, I booted it on my regular computer.

Hp mediasmart server ex470 linux install#

The ISO image is an installer drive, and it'll then install OpenMediaVault onto your second flash drive. The wiki installation instructions weren't clear on this, but you'll then need a second flash drive on which to install OpenMediaVault. My other computer was on Windows, so I then used to restore the image onto the flash drive. You'll also need a USB keyboard.Дownload the ISO image of OpenMediaVault. To start off with, you need access to a normal computer from which to prepare the install media. I've pasted in my notes on the process below in case it helps anyone else making the transition. At least upon first impression, everything seems to be working other than the internal network adapter, so I've used a USB network adapter in lieu of that. I recently switched my HP EX470 Mediasmart home server from the end-of-lifed Windows Home Server to OpenMediaVault.